United States


support for


get started
& how to

contact us


Mon - Fri

11am - 7pm EST

get started
& how to

Fly Crane - Getting Started

You will need:

  • 1 x Fly Crane Helicopter

  • 1 x Remote Control
  • 6 x AA Premium Alkaline Non-Rechargeable Batteries (not included)
  • 1 x Phillips Screwdriver (not included)

Install the batteries. Open the battery compartment on the back of your controller using a Phillips head screwdriver. Place the 6 AA batteries in the battery compartment, making sure you are putting these in the right way.

Charge your helicopter. Plug the controller wire into the helicopter, move the power switch on the controller into the CHG position, and you will see a blinking red light on the controller. The helicopter is now charging. When the remote lights flash red and green together, your helicopter will be ready to fly.

Check your environment. The Fly Crane Helicopter is an indoor only helicopter, so before flying, make sure you are indoors, away from any other Infrared devices, bright lights, air vents or open windows.

Turn the helicopter and the controller on. Have fun. If you need some more help flying your helicopter, check out some of our other guides!

was this answer helpful? yes > no >

back to top

general info

What more can you tell me about my Fly Crane?

Fly Crane™

Orange and White
Yellow and Grey

Indoor - Indicated on box art

Control Interface:

Frequencies: Channel A
Channel B

Controller Range:
Approx. 20 - 25 ft.

Battery Requirement for Fly Crane™:
Rating: DC 3.7 V, 1,8 W
Batteries: 1 x 3.7 V Li-Poly Rechargeable Battery Pack
Requires: 1 x 3.7 V Li-Poly Rechargeable Battery Pack (included)

Battery Requirement for Controller/Charger:
Rating: DC 9 V, 0,45 W
Batteries: 6 x 1.5 V "AA"/LR6/AM3
Requires: 6 x 1.5 V "AA" size batteries (not included)

Charge Time:
Approx. 35 mins.

Flight Time:
Approx. 5 mins.

Recommended Age:
10 - 12 Years

was this answer helpful? yes > no >

How long will my Fly Crane fly for?

The average flight time for your Fly Crane Helicopter is around 4 to 5 minutes on a full charge. The flight time may vary depending on where you’re flying it, the type of batteries you are using, and how much throttle you give the helicopter!

was this answer helpful? yes > no >

How far can my Fly Crane fly?

The signal is good for around 20-30 feet. This should be plenty of distance for most indoor areas you will be flying your Fly Crane!

was this answer helpful? yes > no >

How long should it take to charge my Fly Crane?

Your Fly Crane will take around 30-45 minutes to charge. You will know when the helicopter is fully charged because the red and green lights will be flashing together!

was this answer helpful? yes > no >

What do the controller / helicopter lights mean for my Fly Crane?

Here are the different types of lights you may get on your remote control or helicopter and what they mean:

Solid Green – Controller ON
Green light Off – Controller OFF
Flashing Green – Replace Batteries
Red Off (on Heli) – Helicopter Off
Flashing Red – Charging
Flashing Red/Green Together – Fully Charged
Flashing Red/Green Alternately – Bad Connection

Are you seeing different lights that aren't on this list? If so, call our Customer Care Department at 1-800-622-8339. They’d love to help!

was this answer helpful? yes > no >

How do I install batteries in my Fly Crane controller?

You will need: (not included with your Fly Crane Helicopter)

  • 1x Phillips Screwdriver

  • 6x AA New Premium Alkaline Non-Rechargeable Batteries of the same brand.

  • AND
  • 1x Fly Crane Helicopter

  • 1x Fly Crane Helicopter Remote Control/Charger

Installing the Batteries
  1. Open the battery door cover using your Phillips Screwdriver.

  2. Remove any used batteries from your remote control.

  3. Put in your new batteries as shown in the battery compartment of your remote.

  4. Using the Phillips Screwdriver, screw in the battery door cover back onto the remote control.

was this answer helpful? yes > no >

Can I fly more than one Fly Crane at a time?

You can fly 2 Fly Crane helicopters together at a time; just make sure you have 2 helicopters in 2 separate frequencies – either A, or B. The frequency will be printed on the front of the box in the lower right hand corner, or on the underside of the helicopter.

was this answer helpful? yes > no >

back to top

troubleshooting & repair

How do I charge my Fly Crane?

What you need:

  • 1x Fly Crane Helicopter

  • 1x Fly Crane Helicopter remote/charger with batteries already installed.

  1. Your remote control for your Fly Crane Helicopter is also your charger. Lift up the charge cable cover located in the middle of your controller indicated by the "Air Hogs" logo.

  2. Make sure that both the Remote and the Fly Crane Helicopter power switches are turned to the "OFF" position.

  3. Plug in the end of the charging wire into the charge port square on the side or bottom of the helicopter. You will want to make sure that the little arrow on the end of the charge cord lines up with the arrow on the charge port of the toy.

  4. Once plugged in, turn the power switch on the Remote Control/Charger down to the "CHG" position. You will know that the Helicopter is charging when you see the Red charging light blinking on the remote.

  5. When your helicopter is fully charged, both the Red charge light and Green power light will flash together. Once complete, turn everything off and unplug and store the cord back in the remote. You are now ready to fly!

was this answer helpful? yes > no >

My Fly Crane keeps spinning! What do I do?

If your helicopter is spinning in circles, the first thing you’re going to want to do is check all your rotors to see if there is any hair or debris caught in that area. Even just one little piece of hair can make your helicopter spin out of control!

Now try and fly your helicopter. If it’s still spinning, the next step would be to “trim” your helicopter.
See that little dial on your controller that says "Trim"? This will help you get your helicopter to stop spinning.

Setting the Trim:

  1. Figure out which direction your helicopter is spinning. Are you spinning to the left (counter-clockwise) or to the right (clockwise)?

  2. Make sure your remote is pointed at the helicopter for the best possible response.

  3. Give your helicopter a bit of throttle and get it up in the air. Start trimming in the opposite direction of the spin.
    • If your helicopter is spinning to the right (clockwise), turn the trim dial counter-clockwise.
    • Same thing goes for the other way around. If your helicopter is spinning to the left (counter-clockwise), turn the trim dial clockwise.

The trim might need to be fixed after charging the helicopter and it will definitely need to be adjusted after crashes!

Sometimes you’ll need to rotate the trim dial only 5 times or so, and sometimes you’ll need to rotate the trim dial up to 50 times. Try trimming it just a little bit. If it seems like it’s working, but it’s not quite there yet, turn it a few times more. It’ll even out eventually, so be patient!

If your helicopter starts to spin the other way after trimming, you may have over-trimmed! If this happens, all you need to do is trim it in the opposite direction.

If you’ve trimmed your helicopter and it is still spinning in circles, check for the following:

Signal Interference: Fly indoors. Sunlight and other strong light sources may interfere with the signal from the remote to the helicopter, so try and stay away from these. Make sure you are also not flying around other R/C product that might be sharing the same channel/frequency/bandwidth.
Batteries: For trimming to work, your helicopter needs to be fully charged. Make sure you are using brand new, premium, non-rechargeable batteries.

If your helicopter is still spinning, give our Customer Care Team a call at 1-800-622-8339 and they’ll love to help out!

was this answer helpful? yes > no >

Are there parts available for my Fly Crane?

Although there are no replaceable parts for this heli, we would love to see if there is anything we can do for you. Give our Customer Care Department a call at 1-800-622-8339 and they will be glad to help you out!

was this answer helpful? yes > no >

back to top